Geekvape Wenax M1 Vape Kit

  • $16.19
  • Ex Tax: $16.19
  • Product Code: M00000496
  • Availability: In Stock

Available Options

The Geekvape Wenax M1 vape kit is a compact and simple device, ideal for new and seasoned vapers alike. The kit’s built-in 800mAh battery can support long sessions of vaping, while its power output range of 9-16W provides consistent performance regardless of battery level. Plus, the MTL (Mouth To Lung) style inhale feels similar to a cigarette and creates a more noticeable throat hit.

Features:

  • MTL Pod Kit
  • 800mAh Built-In Battery
  • Inhale Activation
  • Pocket-Friendly Design
  • 2ml Refillable Pods
  • 0.8 Ohm Built-In Mesh Coils

The device’s minimalist design and inhale activation means that you won’t have to worry about navigating menu screens and clicking buttons. Just inhale on the device’s mouthpiece and you’re good to go. The adaptive power setting will automatically select the correct wattage for your chosen pod, helping to increase its lifespan.

Refilling your Wenax M1 pod is easy, thanks to the side-filling system. Just unplug the stopper to top up with e-liquid. It features a built-in coil design, so there’s no need to change coils. Instead, you can simply replace the old pod with a fresh one. The Wenax M1 pods boast a clear design that makes it easier to monitor your e-liquid levels. Included with your kit is a 0.8 Ohm Wenax M1 pod, but a 1.2 Ohm option which will deliver a more restricted inhale is also available separately. Both of these pods offer an MTL-style inhale, so we suggest using this kit with 50% PG e-liquids or higher for best results.

Please note, this kit does not come with a charging cable.

Contains:

  • Geekvape Wenax M1 Vape Device
  • 0.8 Ohm Geekvape Wenax M1 Pod
  • User Manual

How To Set Up & Use Your GeekVape Wenax M1

Charge Your Wenax M1 Battery

Make sure your kit is fully charged before using it. You can use a USB-C cable to recharge and this will take a little under an hour from 0% charge.

Prepare Your Wenax Pod For Filling

Remove the pod from your kit and locate the rubber bung on the side. Remove this rubber insert to reveal the pod’s filling port.

Fill Your Wenax Vape Pod

Hold your Wenax pod with the filling port facing upwards, and then put the nib of your e-liquid bottle into the port and squeeze.

Reassemble Your Wenax Pod

When you’re finished filling, re-insert the rubber bung back into the pod. Push it in firmly to make sure it’s secure.

Prime your Wenax Pod

Leave your pod upright for ten minutes. Known as “priming your coil” this gives the e-liquid to soak into the pod’s coil.

Reassemble & Vape Your Wenax M1

Put the pod back into your kit – the magnets will keep it secure. Then inhale on the mouthpiece to start vaping.

The Geekvape Wenax M1 vape kit is available in a variety of colours including Gradient Orange, Gunmetal and Red-Blue.
The Geekvape Wenax M1 is shaped like a cigar and weighs just 34g, so it will easily fit in your pocket for on the go vaping.
The Geekvape Wenax M1 vape kit features a clear window, so you can see how much e-liquid you have left, as well as a rubber drip tip for maximum comfort.
You’ll experience consistent power with the Geekvape Wenax M1 vape kit, as the power output remains at a steady pace.
The Geekvape Wenax M1 vape kit will deliver a tight MTL style inhale that imitates the feel of a cigarette.

Write a review

Note: HTML is not translated!
    Bad           Good